AskDefine | Define servomechanism

Dictionary Definition

servomechanism n : control system that converts a small mechanical motion into one requiring much greater power; may include a negative feedback system [syn: servo, servosystem]

User Contributed Dictionary

English

Alternative spellings

Noun

(abbreviated as servo)

Synonyms

Extensive Definition

A servomechanism, or servo is an automatic device which uses error-sensing feedback to correct the performance of a mechanism. The term correctly applies only to systems where the feedback or error-correction signals help control mechanical position or other parameters. For example an automotive power window control is not a servomechanism, as there is no automatic feedback which controls position—the operator does this by observation. By contrast the car's cruise control uses closed loop feedback, which classifies it as a servomechanism.
On the other hand, the line between servo control and negative feedback is in general blurred in the context of cybernetics, where it is thought that a human being can actually serve as a part of a servo loop, and that quite a number of human behaviors can be explained as being instances of such control within the context of the organic world.
Servomechanisms may or may not use a servomotor. For example a household furnace controlled by thermostat is a servomechanism, yet there is no closed-loop control of a servomotor.
A common type of servo provides position control. Servos are commonly electrical or partially electronic in nature, using an electric motor as the primary means of creating mechanical force. Other types of servos use hydraulics, pneumatics, or magnetic principles. Usually, servos operate on the principle of negative feedback, where the control input is compared to the actual position of the mechanical system as measured by some sort of transducer at the output. Any difference between the actual and wanted values (an "error signal") is amplified and used to drive the system in the direction necessary to reduce or eliminate the error. An entire science known as control theory has been developed on this type of system.
Servomechanisms were first used in military fire-control and marine navigation equipment. Today servomechanisms are used in automatic machine tools, satellite-tracking antennas, automatic navigation systems on boats and planes, and antiaircraft-gun control systems. Other examples are fly-by-wire systems in aircraft which use servos to actuate the aircraft's control surfaces, and radio-controlled models which use RC servos for the same purpose. Many autofocus cameras also use a servomechanism to accurately move the lens, and thus adjust the focus. A modern hard disk drive has a magnetic servo system with sub-micron positioning accuracy.
Typical servos give a rotary (angular) output. Linear types are common as well, using a screw thread or a linear motor to give linear motion.
Another device commonly referred to as a servo is used in automobiles to amplify the steering or braking force applied by the driver. In this form this device is not a true servo, but rather a mechanical amplifier.
In industrial machines, servos are used to perform complex motion.

History

James Watt's steam engine governor, an automatic speed control, is generally considered the first powered feedback system. The windmill fantail is an earlier example of automatic control, but since it does not have an amplifier or gain, it is not usually considered a servomechanism.
The first feedback position control device was the ship steering engine, used to position the rudder of large ships based on the position of ship's wheel. This technology was first used on the SS Great Eastern in 1866. Steam steering engines had the characteristics of a modern servomechanism: an input, an output, an error signal, and a means for amplifying the error signal used for negative feedback to drive the error towards zero.
Electrical servomechanisms require a power amplifier. World War II saw the development of electrical fire control servomechanisms, using an amplidyne as the power amplifier. Vacuum tube amplifiers were used in the UNISERVO tape drive for the UNIVAC I computer.
Modern servomechanisms use solid state power amplifiers, usually built from MOSFET or thyristor devices. Small servos may use power transistors.

RC servos

2. position feedback potentiometer 3. reduction gear 4. actuator arm]] RC servos are hobbyist remote control devices servos typically employed in radio-controlled models, where they are used to provide actuation for various mechanical systems such as the steering of a car, the flaps on a plane, or the rudder of a boat.
RC servos are composed of a DC motor mechanically linked to a potentiometer. Pulse-width modulation (PWM) signals sent to the servo are translated into position commands by electronics inside the servo. When the servo is commanded to rotate, the DC motor is powered until the potentiometer reaches the value corresponding to the commanded position.
Due to their affordability, reliability, and simplicity of control by microprocessors, RC servos are often used in small-scale robotics applications.
The servo is controlled by three wires: ground (usually black/orange), power (red) and control (brown/other colour). This wiring sequence is not true for all servos, for example the S03NXF Std. Servo is wired as brown(negative), red (positive) and orange (signal). The servo will move based on the pulses sent over the control wire, which set the angle of the actuator arm. The servo expects a pulse every 20 ms in order to gain correct information about the angle. The width of the servo pulse dictates the range of the servo's angular motion. A servo pulse of 1.5 ms width will set the servo to its "neutral" position, or 90°. For example a servo pulse of 1.25 ms could set the servo to 0° and a pulse of 1.75 ms could set the servo to 180°. The physical limits and timings of the servo hardware varies between brands and models, but a general servo's angular motion will travel somewhere in the range of 180° - 210° and the neutral position is almost always at 1.5 ms.
Servo motors are often powered from nickel-cadmium battery packs common to most RC devices. Voltage ratings vary from product to product, but most servos are operated at 4.8 V or 6 V DC from a 4 or 5 cell battery.

See also

servomechanism in Czech: Servomotor
servomechanism in Danish: Servomekanisme
servomechanism in German: Servogerät
servomechanism in Estonian: Servomootor
servomechanism in Spanish: Servomotor
servomechanism in French: Servomécanisme
servomechanism in Dutch: Servomotor
servomechanism in Japanese: サーボ機構
servomechanism in Polish: Serwomechanizm
servomechanism in Russian: Сервоконтроль
servomechanism in Turkish: Servo motor
servomechanism in Chinese: 伺服機構

Synonyms, Antonyms and Related Words

Flettner control, action, autosyn, clockworks, cybernion, direct-current servo, drive train, gear, hemostat, hydraulic servo, innards, machinery, mechanism, motion, movement, movements, pneumatic servo, power brake, power servo, power train, selsyn, servo, servo brake, servomotor, servotab, sine mechanism, synchro, synchro receiver, synchro transmitter, synchronous motor, telemechanism, watchworks, wheels, wheels within wheels, workings, works
Privacy Policy, About Us, Terms and Conditions, Contact Us
Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2
Material from Wikipedia, Wiktionary, Dict
Valid HTML 4.01 Strict, Valid CSS Level 2.1